Glossary of Wheel Terms

Back Space: the distance from the mounting surface of the wheel to the back flange of the wheel. By comparing the back space measurement of a custom wheel to a stock wheel, then allowing for any differences in rim width, clearance requirements can be determined. 

Bead Seat Area: position on wheel where bead area of tire rests on inside of rim and makes a positive seal. 

Mag Wheels: cast magnesium wheels - used primarily as pure racing wheels because of their light weight. It is a commonly misused term to describe all custom wheels ("mag wheels"), whether magnesium or another material. 

Mounting Pad, or Surface: the back of the wheel center that makes contact with the brake drum, rotor, or hub flange on a vehicle. 

Drilled Bolt Pattern: a wheel precision drilled for a specific vehicle application, as opposed to a multi-fit bolt pattern. 

Multi-fit Bolt Pattern: a custom wheel precision drilled to accept 2 or 3 bolt patterns. (e.g.-Superior's Superbug design that fits 4-1/2", 4-3/4" and 5"). 

Bolt Pattern (Bolt circle diameter): the diameter of an imaginary circle drawn through the center of each lug. This is how custom wheels are usually described in lieu of specific car applications (i.e. 4-3/4" on 5. In this case, 5 denotes the number of lugs.) 

Offset: the distance between mounting surface (bolt pad) of the wheel and the center line of the wheel (All wheels have offset, even if it is zero). 

Negative Offset: when the back of the mounting surface (bolt pad) is closer to the disc/drum side of the wheel. Negative offset increases the "track" of the vehicle, because the center line is moved away from the vehicle towards the street. This is what is referred to as the "deep dish" look. 

Positive Offset: when the back of the mounting surface (bolt pad) is closer to the street side of the wheel. Positive offset reduces the "track" of the vehicle because the center line is moved away from the street towards the vehicle. This is commonly referred to as the toronado style wheel. 

Rim Diameter, Nominal: the height of the wheel measured from a point on a bead seat to a second point on the same bead seat 180-degrees apart. It is the rim diameter that appears in the designation of the tire size (e.g. P235/70R15). 

Rim Width: the width of the wheel measured from the front bead seat to the rear bead seat. In order to achieve a balance between ride, handling, and wear for street driven tires, the rim width should equal about 75% of the tire section width. For improved traction and handling, the rim width should equal about 90% of the tire section width. 

Runout, Lateral: side motion, of wheel wobble, as the wheel rotates; the relationship of the plane of the mounting surface to the vertical plane of the bead seats. 

Runout, Radial: up and down, or wheel hop, of the wheel as it rotates; the relationship of the circumference of the bolt circle to the circumference of the bead seats. 

Spring Weight: vehicle weight supported by the springs, i.e. body mass, interior, engine, transmission, aand chassis. 

Unsprung Weight: combined weight of all suspension components that are not supported by the springs. This includes shocks, tires, wheels, brake and axle assemblies. Reducing unsprung weight will improve ride and handling characteristics. 

3 Basic Types of Custom Wheels 

There are three basic types of custom wheel construction available in the custom aftermarket. The first is the one-piece, cast aluminum wheel. 

The two-piece modular wheel has a center section, made of aluminum or steel which is fastened to an aluminum or steel rim.

The three-piece modular wheel is composed of two outer halves that make up the rim, plus the wheel's center section.  

Special Twists in Torquing Custom Wheels 

Extreme care should be taken when working with and torquing the special lug nuts that come with custom wheels. (You should use only the lugs that are supplied with the wheel to insure proper seating and lug length.) First of all, test the nuts on the lug for proper length and size before installation of the assembled wheel and tire. Excessive lug length will cause bottoming out of the nut. Some wheels may require spacers to clear disc brake components. In any event, the hex nut must be tightened onto the stud to a length equal to the diameter of the stud. Then clean the lugs, removing all rust and dirt. The lugs should be dry, and their threads should have no stripping. As far as lubricating the lugs check the wheel manufacturer's specifications. 

UNDER NO CONDITIONS SHOULD LUG NUTS BE TORQUED DOWN WITH ANYTHING BUT A CALIBRATED TORQUE WRENCH. AND THE WRENCH SHOULD BE EQUIPPED WITH A PLASTIC OR TEFLON INSERT. NEVER USE POWER OR IMPACT WRENCHES. CUSTOM WHEEL LUG NUTS HAVE FINISHES THAT ARE EASILY DAMAGED BY MISHANDLING. A TORQUE WRENCH WILL ALSO ELIMINATE ANY POSSIBLE CROSS-THREADING OR STRIPPING. Lug nuts should be tightened in a cross pattern for 4, 6, and 8-lug bolt circles... and in a star pattern for 5-lug circles. Never tighten two adjacent lug nuts. In this way, you will assure uniform pressure and prevent wheel misalignment. 

Also, as an additional service, be sure to check a customer's lug wrench to make sure it works with the new lugs. And remember to leave a set of original lugs for the customer's spare tire. 

For recommended torque, always refer first to the ratings found in the owner's manual. They take precedence over the specifications listed in the torque chart below: 

 Lug Nut/Bolt Diameter  Torque in FT/LBS
 3/8" 35-45
7/16" 55-65
1/2" 75-85
9/16" 95-115
12mm 70-80
14mm 85-95

                                                     

Remember also that you should use a non-metallic tool such as a rubber hammer for tapping in snap-on type center caps. 

What Kind of Weights...And Where

In balancing your wheel and tire assembly, you want to be certain that you apply the correct wheel weights in the proper location. 

Before installing your wheel and tire assembly on the vehicle, position it in place and "test fit" for proper fender clearance. Make sure that the fender, molding or suspension members do not interfere with tire rotation in either a straight or turning direction. 

The Fit Must Be Flush

It is important that you make a trial fit of the wheel on the vehicle before mounting the tire. The wheel must go into place freely. It should never be forced to seat against the hub by the application of lug nut pressure. Check to make certain that the bolt circle is correct. The wheel hub mounting and rotor surfaces must be clean and free of dirt and grease. There should also be no obstructions, such as spring clip retainers, brake drum rivets, or balancing weights...anything that may create an improper fit. There obstructions must be removed or ground down to provide the necessary flush fit. In addition, make sure that the wheel does not foul the brake drum and/or caliper, any other part of the braking system, or any part of the body. 

The bead area of the custom wheel should be treated with the utmost care. Any old lubricant, rust, or rubber deposits must be removed. Do not use sandpaper, steel wool or a wire brush, as you might on standard steel wheels. Instead, use non-abrasive cleaning pads or cleaners made especially for custom wheels. 

Custom Wheels Glossary

Aspect Ratio: the dimensional relationship between tire height and width; section height divided by section width; expressed as a percent value. 

Backspacing: the measurement from the back of the bolt pad to the back edge of the rim; used to calculate offset and determine where the back of the bolt pad is located in relation to the rim width, sometimes referred to as rearspacing.

Balance: the even distribution of the tire, wheel, and brake assembly to the center point of the assembly. 

Bead Seat: the position where the tire sits and seals on the inside of the rim.

Bolt Circle: often referred to as the bolt pattern; the diameter of an imaginary circle drawn through the center of each lug hole. 

Cross Pattern: the sequential torquing of the lug nuts in a pattern across from one another. 

Custom Wheel: an aftermarket wheel designed to improve performance and enhance appearance and comprised of one, two, or three pieces. 

Deflection: a turning or bending of the tire/wheel assembly, caused by the flexing of the wheel and resulting in reduced performance. 

Ducts: open areas in the design of a specialty wheel which direct cooling air to brake components. 

Flush Fit: a condition where the mounting pad of the wheel goes into place freely and without obstruction against the hub mounting surface. 

High Pressure Die Cast: a wheel manufacturing process using aluminum alloys in special high pressure die casting machines. 

Hub Centric: a situation where the center bore hole of a wheel is made to match up with the hub diameter of the vehicle; the wheel is then centered by the center hole, rather than the lug nuts.

Load Rating: the weight that a wheel is designed to support in normal service. 

Lug Centric: the centering of the wheel by matching it up with the lug nuts, rather than by the center bore hole of the wheel; hub centric is the more accurate centering method.

Mag: a misleading description of specialty wheels; with the exception of pure racing wheels; specialty wheels contain little or no magnesium. 

Mounting Pad: the surface area of the back of the wheel's center that contacts the brake drum or hub flange of the vehicle. 

Negative Offset: when the back of the bolt pad is closer to the inside of the wheel; when the mounting face is inboard of the rim centerline; extends assembly away from vehicle resulting in wider tracking. 

Offset: the distance from the centerline of the wheel to the mounting face of the wheel. 

One-Piece Wheel: used to describe an aluminum specialty wheel that is cast in one piece; also the standard steel wheel found as OEM on production cars. (OEM wheels are typically two piece). 

Permanent Mold: the manufacturing of wheels by one of three processes...centrifugal casting, low pressure die casting, or permanent mold die casting. 

Plus 1/Plus 2 Concept: a new concept to improve handling and performance through the mounting of tires with wider section widths and lower section heights to rims of 1, 2 and sometimes even 3 inches greater diameter. 

Positive Offset: when the back of the bolt pad is closer to the street side of the wheel; when the mounting face is outboard of the rim centerline, draws assembly towards the vehicle resulting in narrower tracking. 

Rear Spacing: see Back spacing

Rim Bell: the area between the edge of the wheel's rim and the rim drop area. 

Rim Diameter: the diameter of the bead seat, not the diameter of the rim edge. 

Rim Drop: the area of the wheel's rim having the smallest diameter. 

Rim Flange: the outermost edge of a wheel's rim to which clip-on weights are attached.

Rim Width: the width of a wheel measured from the outside corner of each bead seat, not from the outside edges of the wheel. 

Safety Bead: the raised area circling the rime of the wheel and located slightly inward from the beat seat; required on all specialty wheels driven in street use to keep the tire from slipping off the rim bell, if accidentally deflated. 

Spacers: metal plates used between the wheel rim and mounting hub that permit wheel adjustments in mounting and installation.

Specialty Wheel: same as Custom Wheel 

Star Pattern: the proper method for sequential torquing of lug nuts in a 5-lug bolt circle. 

Three-piece Wheel: a specialty wheel composed of two outer rim halves, usually made of aluminum alloy, and a center section of pressure-cast aluminum or magnesium alloy. The center is either bolted or rivetted to the rim. 

Torque: the product of a force applied through a lever arm to cause rotation. 

Torquing: the securing of the tire/wheel assembly to the vehicle by the tightening of the wheel's lug nuts to the studs of the vehicle's hub; in the case of specialty wheels, torquing should always be done with a manual torque wrench, containing an insert socket of plastic or teflon. 

Torque Rating: the proper pressure, expressed in foot-pounds, for tightening lug nuts of various diameters. 

Truing Tuning: the proper adjustment of spokes in a wire wheel...or of the center section in a two-piece wheel...to align the bolt circle into the correct position in the outer rim. 

Two-Piece Wheel: a specialty wheel comprising a center section of aluminum or steel that is fastened to an aluminum or steel rim. 

Unsprung Weight: the total weight of a vehicle not supported by the suspension system; wheels and tires are prime examples. 

Ventilation: an open wheel design that scoops in air and forces it over brake pads and drums to prevent overheating and brake fading. 

Wheel Solvents: cleaning compounds that are specially formulated for use on specialty wheels to prevent discoloration and spotting. 

Wheel Weights: weights that are either clipped, taped, or self-adhered to the inside or outside of the wheel in order to balance the tire / wheel assembly. 

Zero Offset: when the centerline of the wheel coincides exactly with the mounting face. 

Be On Target With Offset 

The growth of the custom wheel market has placed new emphasis on some concepts that affect wheel selection and application. They are somewhat technical and confusing, but they need to be mastered if you want a thorough knowledge of custom wheels. 

The first is offset. This is the measured difference between the mounting face of the center membrane of the wheel and the centerline of the rim. You have zero offset when the wheel's centerline coincides exactly with the mounting face. 

Positive offset occurs when the mounting face of the wheel is to the outside of the wheel's center axis or centerline. Positive offset is usually found on the wheels of front wheel drive vehicles. It tucks the wheel and tire under the fender. 

A wheel has negative offset when the hypothetical centerline is outboard of the mounting face of the wheel. The effect that is produced is a wider track. Excessive negative offset will increase steering wheel kick-back and places greater additional stress on wheel bearings. 

Since offset determines the relative positioning of the wheel/tire assembly to the front axle steering geometry, front axle offsets should be kept as close as possible to the factory-designed. In this way, steering input will cause the tire to pivot on the intended design point. 

Backspacing...No Room For Error

This brings us to another concept called backspacing or rear spacing. Backspacing is easy to measure and lets you calculate the offset of a wheel. It refers to the distance measured from the back edge of the wheel to the back of the mounting face. To measure backspacing, place the wheel flat down on a smooth surface. Lay a straight edge across the back (inboard) edge of the wheel and measure with a ruler down to the mounting pad. This backspacing minus the rim width divided by two equals offset. See the formula below: 

A positive number means the wheel has positive offset. A negative number means the wheel has negative offset. Proper offset and backspacing will assure the correct amount of loading on the wheel bearings for increased wheel bearing life and longer-lasting suspension systems. Your guiding principle in upgrading wheels should be to select custom wheels whose offset comes as close as possible to the manufacturer's specifications for the vehicle's OEM wheels. If you need to really change the offset, you might have to upgrade the suspension system as well. 

Know Your Wheel Widths...In-Depth

The key principle to always bear in mind when selecting custom wheels is that wider wheels provide better handling. Specifically, this means a rim width in the "wide side" of the rim width range, but within recommended maximums. 

(See the "T/A Fitment Guide" for more information on specific applications)

Wheels and Braking

Wheels can have an effect on braking efficiency due to three design elements...weight, material construction, and "ventilation". While the overall difference in weight is very slight, lighter custom wheels can decrease the load on the braking system. 

Wheels can also perform a major function in brake cooling. Under heavy braking conditions, heat build-up can cause brakes to fade or lose efficiency. As a result, some wheels have been designed to facilitate brake cooling. As a general rule, the larger the open space in wheel design, the greater the normal air flow over the brakes and through the wheels. Some wheels have been specifically designed with a great deal of void space, such as cross spoke designs. 

Solid wheels restrict air passage. For this reason, separate air ducting may be required. Air ducting wheel designs and/or cooling fans have been designed to literally scoop air out from under the car and through the wheels. These systems work well on racing cars. But the car's aerodynamic efficiency can be affected. 

The increased wheel diameters obtained through the Plus 1/Plus 2 concept can also contribute to improved brake cooling by providing a larger area for air passage around the brakes. 

Another thing to remember is that all wheels flex to some degree. The greater the amount of flex, the more the total tire and wheel combination will deflect...and this will reduce performance. Most custom wheels are design to maximize stiffness to reduce total tire/suspension deflection. And, of course, it is a must that every custom wheel have an acceptable load capacity for the application involved. 

Bolt Circle and Hub Centric 


In converting to custom wheels, it is vital that the wheel fit into place freely. The bolt pattern or bolt circle must be correct. Bolt circle, then, is another concept with which you should be completely familiar, since it is how custom wheels are usually described when specific car applications are not available. Bolt circle is the diameter of an imaginary circle drawn through the center of each lug hole, whether it is a 4-lug, 5-lug, 6-lug, or even an 8-lug pattern. For example, the term "4x100mm" describes a 4-lug hole pattern on a circle with a 100mm diameter. For a 4-lug, 6-lug, or 8-lug pattern, you measure from the middle of two holes directly across from one another. This is obviously impossible with a 5-lug pattern, and so the easiest way is the measure from the back of a hole to the center of the second hole. 

Then, there is the concept of "hub centric". This occurs when the center hole bore of a wheel is made to match up to the hub diameter of a wheel. For example, a 57mm wheel hub bore should perfectly match a 57mm hub. The wheel is then centered by the center hole rather than the lug nuts. In other words, it is hub centric as opposed to lug centric. 

Auto manufacturers use hub centric wheels because it is a more accurate way to locate wheels on a car. Only the most expensive aftermarket wheels, designed for an individual car, use hub centric location. 

Lug Centric wheels are located only by the lug nuts. This leaves room for error in locating a wheel on the hub, particularly when shouldered lug nuts rather than tapered nuts are used. 

General Rules for Custom Wheels

Along with the basic concepts just discussed, you should always remember some general rules in installing a wheel to your vehicle. Lighter weight wheels improve and provide better performance. It simply requires less energy to accelerate them, and wider rim widths produce a more stable contact patch. In addition, because of lower unsprung weight the suspension is capable of responding more quickly to changes in the road surface which can help the suspension keep the tires in better contact with the road surface, particularly under rough road conditions. 

The Importance of Mounting and Installation

The selection of the correct custom wheel with the correct high performance T / A Radial is only half the job, however. Equally important is proper mounting and installation. Lack of expertise in the use of mounting equipment, plus lack of knowledge and poor handling by untrained service personnel, can ruin wheel and tire performance. Custom wheels and premium tires are major investments and they should have all the extra attention and expertise that they deserve. 

Wheel Problems - And How To Avoid Them

  • Improper Wheel Application

 Make certain that wheels have the right offset and/or bolt pattern for a particular fitment.

  • Use of lug nuts/bolts not designed for use with a particular wheel 

Always check wheel manufacturer's specifications, particularly for proper lug shank length.

  • Use of high-speed Impact wrenches during installation

Custom wheels should be installed and lugs should be tightened with torque wrenches in accordance with manufacturer's specifications. 

              Using Spacers

              Spacers are sometimes necessary in a custom wheel application to keep the wheel "off" a brake caliper, wheel bearing, ball joint or inner fender member. Spacers can, however, have a negative effect on camber settings and may increase tire rubbing or scuffing. Another serious consideration is that, with the addition of spacers, longer lug bolts may be required. CARE MUST BE TAKEN. ALWAYS CHECK WITH THE WHEEL MANUFACTURER FOR RECOMMENDATIONS ON THE PROPER USE OF SPACERS. 

              Road Test for Clearance

              Another step you should take in the installation of custom wheels is a thorough road test. Before actually driving the car, turn the front wheels from side to side to check for any interference. Also compress the suspension and check for any possible contact. 

              Drive the car at very low speeds as a final precaution. Then make sure the tire and wheel are not disturbing the body. Do this either by driving the car under a full load. Work in and out of angled driveways and turn in complete hard circles. After 10 to 25 miles of driving, retorque to specific ratings.